Search results for: 'WA 0859 3970 0884 Biaya Bikin Taman Mini Di Balkon Murah Pundong Bantul'

Cod. 00200530.1
IXEF body, Viton OR and PTFE-Teflon gaskets, AISI 316 stainless steel ball. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate up to 600 lt/min. 8 seconds closing time, 0,2 Amp nominal absorption. The special setting of the section hole of the valve guarantees an exact and accurate control of flow. If applied along the lineat suction of a centrifugal pump, it allows a better steadiness of flow.

Cod. 00200500
"IXEF body, Viton OR and Teflon-PTFE gaskets, AISI 316 stainless steel ball with continuous flow system. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate up to 500 lt/min. 1,3 seconds closing time, 0,3 nominal absorption. Also available with lateral or lower inlet."

Cod. 00200501
"IXEF body, Viton OR and Teflon-PTFE gaskets, AISI 316 stainless steel ball with continuous flow system. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate up to 500 lt/min. 1,3 seconds closing time, 0,3 nominal absorption. Also available with lateral or lower inlet."

Cod. 00200701.ME
"Plastic body, Viton OR and Teflon-PTFE gaskets, plastic ball. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate beyond 1000 lt/min on the 2” ½ model. 3 seconds closing time, 0,6 Amp nominal absorption. Available in the ON/OFF and PROPORTIONAL versions with the opportunity of applying the angular sensor to detect the position of the ball."

Cod. 00200701
"Plastic body, Viton OR and Teflon-PTFE gaskets, plastic ball. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate beyond 1000 lt/min on the 2” ½ model. 3 seconds closing time, 0,6 Amp nominal absorption. Available in the ON/OFF and PROPORTIONAL versions with the opportunity of applying the angular sensor to detect the position of the ball."

Cod. 413L0399

Cod. 68112199
The electrohydraulic motor drive system applicable to all the 5-way (4 outlets) and 6-way (5 outlets) ball valves allows reaching any position using a hydraulic feed with a minimum pressure of 40 bar. The solenoid valve integrated in the system is connected to a 12VDC control which displays the ball position. There are three types of sensor to determine the position: microswitches, reed sensors and sensors for the radio frequency control.

Cod. 68110499
The electrohydraulic motor drive system applicable to all the 5-way (4 outlets) and 6-way (5 outlets) ball valves allows reaching any position using a hydraulic feed with a minimum pressure of 40 bar. The solenoid valve integrated in the system is connected to a 12VDC control which displays the ball position. There are three types of sensor to determine the position: microswitches, reed sensors and sensors for the radio frequency control.

Cod. 68110399
The electrohydraulic motor drive system applicable to all the 5-way (4 outlets) and 6-way (5 outlets) ball valves allows reaching any position using a hydraulic feed with a minimum pressure of 40 bar. The solenoid valve integrated in the system is connected to a 12VDC control which displays the ball position. There are three types of sensor to determine the position: microswitches, reed sensors and sensors for the radio frequency control.

Cod. 68110299
The electrohydraulic motor drive system applicable to all the 5-way (4 outlets) and 6-way (5 outlets) ball valves allows reaching any position using a hydraulic feed with a minimum pressure of 40 bar. The solenoid valve integrated in the system is connected to a 12VDC control which displays the ball position. There are three types of sensor to determine the position: microswitches, reed sensors and sensors for the radio frequency control.

Cod. 68121799
The electrohydraulic motor drive system applicable to all the 5-way (4 outlets) and 6-way (5 outlets) ball valves allows reaching any position using a hydraulic feed with a minimum pressure of 40 bar. The solenoid valve integrated in the system is connected to a 12VDC control which displays the ball position. There are three types of sensor to determine the position: microswitches, reed sensors and sensors for the radio frequency control.

Cod. CH370000
INSTRUMENT FOR MEASURING AND READING REVOLUTIONS PER MINUTE. The 12 VDC powered, backlit Pony RPM in real-time measures the RPM of any rotary shaft fitted with a toothed measuring disk connected to the display. It is equipped with a device for remote control of an actuator or electric motor to increase or decrease the RPM. The operator can set the minimum and maximum value via the keypad together with the “0” value. Suitable for use with weeding booms with air sleeve.

Cod. 30308899

Cod. M0377045
"MAGNETIC INDUCTION FLOWMETER 12 volts powered, square wave sensor without internal moving parts. Available in the versions with Delrin or polypropylene tunnel, 316 stainless steel bushings. Suitable for all water-based liquid chimicals. The inductive magnetic flowmeter consists of a centraI insulated part enclosed in a metal screen made of different types of material, copper and stainless steel, to which the rigorously insulated electronic operating components are connected. At the ends different attachments may be fitted to allow rapid and compact coupling to other components of the sprayer control units. This inductive magnetic flowmeter has a completely open tunnel without moving parts, indispensable for measurement of certain liquids. The mixtures used in agricolture may have different characteristics owing to the viscosity of the chemical and the temperature."

Cod. 00377045
"MAGNETIC INDUCTION FLOWMETER 12 volts powered, square wave sensor without internal moving parts. Available in the versions with Delrin or polypropylene tunnel, 316 stainless steel bushings. Suitable for all water-based liquid chimicals. The inductive magnetic flowmeter consists of a centraI insulated part enclosed in a metal screen made of different types of material, copper and stainless steel, to which the rigorously insulated electronic operating components are connected. At the ends different attachments may be fitted to allow rapid and compact coupling to other components of the sprayer control units. This inductive magnetic flowmeter has a completely open tunnel without moving parts, indispensable for measurement of certain liquids. The mixtures used in agricolture may have different characteristics owing to the viscosity of the chemical and the temperature."