Search results for: 'WA 0852 2611 9277 RAB Pasang Interior Set Kamar Minimalis Apartemen The Cityland Bekasi'

Cod. 63550599
These are used to clean the internal walls of the tanks and the chemical product mixers. The fluid-activated rotating heads perform a total 360° cleaning cycle. Made of non-corroding material. Connections: top male ½” BSP with hosetail and side female 3/8” BSP. Models with interchangeable nozzles allow the consumption and rotation speed to be varied. The nozzle directions can be adjusted. Tap models make it easy to fit and use a hydraulic power supply, when necessary, without the need for additional valves. Supplied with 13 mm connection, Ø10mm connectors available on request.

Cod. 00200530.1
IXEF body, Viton OR and PTFE-Teflon gaskets, AISI 316 stainless steel ball. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate up to 600 lt/min. 8 seconds closing time, 0,2 Amp nominal absorption. The special setting of the section hole of the valve guarantees an exact and accurate control of flow. If applied along the lineat suction of a centrifugal pump, it allows a better steadiness of flow.

Cod. 6M41259V
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 6341259V
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. P1M00630
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. P1000631
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. P1000630
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 6M4121SV
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. P1000307
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 6M41169V
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 6M40849S
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 6M4116SV
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 63412299
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 63412099
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 63411999
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.