Search results for: 'WA 0859 3970 0884 Design Interior Ruangan Mri Di Jebres Surakarta'

Cod. 68121799
The electrohydraulic motor drive system applicable to all the 5-way (4 outlets) and 6-way (5 outlets) ball valves allows reaching any position using a hydraulic feed with a minimum pressure of 40 bar. The solenoid valve integrated in the system is connected to a 12VDC control which displays the ball position. There are three types of sensor to determine the position: microswitches, reed sensors and sensors for the radio frequency control.

Cod. 00200092
FLOW SWITCHING VALVE WITH GEARED REDUCTION MOTOR. Treated aluminium body with cataphoresis cycle. O.R. in Viton and Teflon-PTFE gasket. Interchangeable nylon flanges with different connections and in different sizes. Versions: ON/OFF closure used as a general valve and proportional closure as a pressure regulator. The ON/OFF version is available with a bottom and a side connection. Maximum flow with a flange of the same size as the valve: 350 lt./min.-92RPM. 12Vcc reduction motor.

Cod. 00200093
FLOW SWITCHING VALVE WITH GEARED REDUCTION MOTOR. Treated aluminium body with cataphoresis cycle. O.R. in Viton and Teflon-PTFE gasket. Interchangeable nylon flanges with different connections and in different sizes. Versions: ON/OFF closure used as a general valve and proportional closure as a pressure regulator. The ON/OFF version is available with a bottom and a side connection. Maximum flow with a flange of the same size as the valve: 350 lt./min.-92RPM. 12Vcc reduction motor.

Cod. 00200096
FLOW SWITCHING VALVE WITH GEARED REDUCTION MOTOR. Treated aluminium body with cataphoresis cycle. O.R. in Viton and Teflon-PTFE gasket. Interchangeable nylon flanges with different connections and in different sizes. Versions: ON/OFF closure used as a general valve and proportional closure as a pressure regulator. The ON/OFF version is available with a bottom and a side connection. Maximum flow with a flange of the same size as the valve: 350 lt./min.-92RPM. 12Vcc reduction motor.

Cod. 00200095
FLOW SWITCHING VALVE WITH GEARED REDUCTION MOTOR. Treated aluminium body with cataphoresis cycle. O.R. in Viton and Teflon-PTFE gasket. Interchangeable nylon flanges with different connections and in different sizes. Versions: ON/OFF closure used as a general valve and proportional closure as a pressure regulator. The ON/OFF version is available with a bottom and a side connection. Maximum flow with a flange of the same size as the valve: 350 lt./min.-92RPM. 12Vcc reduction motor.

Cod. 00200094
FLOW SWITCHING VALVE WITH GEARED REDUCTION MOTOR. Treated aluminium body with cataphoresis cycle. O.R. in Viton and Teflon-PTFE gasket. Interchangeable nylon flanges with different connections and in different sizes. Versions: ON/OFF closure used as a general valve and proportional closure as a pressure regulator. The ON/OFF version is available with a bottom and a side connection. Maximum flow with a flange of the same size as the valve: 350 lt./min.-92RPM. 12Vcc reduction motor.

Cod. 00200091
FLOW SWITCHING VALVE WITH GEARED REDUCTION MOTOR. Treated aluminium body with cataphoresis cycle. O.R. in Viton and Teflon-PTFE gasket. Interchangeable nylon flanges with different connections and in different sizes. Versions: ON/OFF closure used as a general valve and proportional closure as a pressure regulator. The ON/OFF version is available with a bottom and a side connection. Maximum flow with a flange of the same size as the valve: 350 lt./min.-92RPM. 12Vcc reduction motor.

Cod. 00200090
FLOW SWITCHING VALVE WITH GEARED REDUCTION MOTOR. Treated aluminium body with cataphoresis cycle. O.R. in Viton and Teflon-PTFE gasket. Interchangeable nylon flanges with different connections and in different sizes. Versions: ON/OFF closure used as a general valve and proportional closure as a pressure regulator. The ON/OFF version is available with a bottom and a side connection. Maximum flow with a flange of the same size as the valve: 350 lt./min.-92RPM. 12Vcc reduction motor.

Cod. P0004072
The pump allows the liquid chemical to be transferred from the manufacturer’s container to the sprayer in maximum safety. The pump is made entirely of polypropylene with Viton seals. It can transfer liquid from 20 litre cans up to 200 litre drums. It is fitted with three different adapters for sampling holes of from 46.5 mm up to 60 mm. The internal tube consists of four pieces that can be adjusted according to the height of the sample receptacle. The metering unit tap can be mounted directly on the pump or it can be left free with a flexible tube. The tap handle can be used in two different operating modes: the first with continuous flow opening, the second, with short pulses for fine metering. It is not necessary for the operator to pump continuously. Flow rate from 8 to 20 litres per minute depending on the viscosity of the liquid.

Cod. 68121999
ELECTRIC CONTROL KIT FOR BALL VALVE. The Control Kit makes it possible to select ball valves outlets remotely and automatically without direct manual intervention on the plant. Polmac produces 12 volt direct current electrical drives for ball valves of various dimensions and characteristics (3-6 way for 1’’ ¼ to 2’’ ½ valves) with 2 different set-ups for a wide range of requirements and characteristics for the plant to be driven: vertical motor-drive with epicyclical reduction gear, horizontal motor-drive with worm-screw reduction gear. 24 Vcc. Motorizations against demand.

Cod. 68121899
ELECTRIC CONTROL KIT FOR BALL VALVE. The Control Kit makes it possible to select ball valves outlets remotely and automatically without direct manual intervention on the plant. Polmac produces 12 volt direct current electrical drives for ball valves of various dimensions and characteristics (3-6 way for 1’’ ¼ to 2’’ ½ valves) with 2 different set-ups for a wide range of requirements and characteristics for the plant to be driven: vertical motor-drive with epicyclical reduction gear, horizontal motor-drive with worm-screw reduction gear. 24 Vcc. Motorizations against demand.

Cod. 68155399
ELECTRIC CONTROL KIT FOR BALL VALVE. The Control Kit makes it possible to select ball valves outlets remotely and automatically without direct manual intervention on the plant. Polmac produces 12 volt direct current electrical drives for ball valves of various dimensions and characteristics (3-6 way for 1’’ ¼ to 2’’ ½ valves) with 2 different set-ups for a wide range of requirements and characteristics for the plant to be driven: vertical motor-drive with epicyclical reduction gear, horizontal motor-drive with worm-screw reduction gear. For the horizontally motorized version a disengagement kit is available (to be ordered separately) to manually drive the valve if necessary. 24 Vcc. Motorizations against demand.

Cod. 6815529A
ELECTRIC CONTROL KIT FOR BALL VALVE. The Control Kit makes it possible to select ball valves outlets remotely and automatically without direct manual intervention on the plant. Polmac produces 12 volt direct current electrical drives for ball valves of various dimensions and characteristics (3-6 way for 1’’ ¼ to 2’’ ½ valves) with 2 different set-ups for a wide range of requirements and characteristics for the plant to be driven: vertical motor-drive with epicyclical reduction gear, horizontal motor-drive with worm-screw reduction gear. For the horizontally motorized version a disengagement kit is available (to be ordered separately) to manually drive the valve if necessary. 24 Vcc. Motorizations against demand.

Cod. 001826DR.VER
ACCESSORY FOR MIXING CHEMICAL PRODUCTS AND WASHING CONTAINERS. Capacity 20 liters. It can be used for mixing: liquid, powdered, and granular chemical products as well as chemical products contained in water-soluble bags. The accessory features a Duplex rotatory nozzle. The following are standard features on all the models: a quick funnel, a nozzle for dissolving products, an external support frame, and an internal inspection port.

Cod. 001826DR.YEL
ACCESSORY FOR MIXING CHEMICAL PRODUCTS AND WASHING CONTAINERS. Capacity 20 liters. It can be used for mixing: liquid, powdered, and granular chemical products as well as chemical products contained in water-soluble bags. The accessory features a Duplex rotatory nozzle. The following are standard features on all the models: a quick funnel, a nozzle for dissolving products, an external support frame, and an internal inspection port.