Search results for: 'WA 0812 2782 5310 Rumah 6x12 4 Kamar Tidur Murah Dukun Kab Magelang'

Cod. 63412499
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 63411699
This product is used to clean chemical products out of emptied containers before they are disposed of. It consists of a central shaft on which rotates a fluid-activated nozzle that is able to rotate through 360° to spray the inner surfaces of the container. The nozzle has tips at its end which allows it to break the protective film on sealed containers holding chemical products. It is made using anticorrosive material. Versions: with 1/2” BSP male connector and 18x1.5 male connector. The version with valve is featured by a fixed nozzle starting to deliver only when the container, overturned, is pressed downwards, allowing the operator to work under safe conditions.

Cod. 00200530.1
IXEF body, Viton OR and PTFE-Teflon gaskets, AISI 316 stainless steel ball. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate up to 600 lt/min. 8 seconds closing time, 0,2 Amp nominal absorption. The special setting of the section hole of the valve guarantees an exact and accurate control of flow. If applied along the lineat suction of a centrifugal pump, it allows a better steadiness of flow.

Cod. 00200500
"IXEF body, Viton OR and Teflon-PTFE gaskets, AISI 316 stainless steel ball with continuous flow system. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate up to 500 lt/min. 1,3 seconds closing time, 0,3 nominal absorption. Also available with lateral or lower inlet."

Cod. 00200501
"IXEF body, Viton OR and Teflon-PTFE gaskets, AISI 316 stainless steel ball with continuous flow system. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate up to 500 lt/min. 1,3 seconds closing time, 0,3 nominal absorption. Also available with lateral or lower inlet."

Cod. 00200701.ME
"Plastic body, Viton OR and Teflon-PTFE gaskets, plastic ball. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate beyond 1000 lt/min on the 2” ½ model. 3 seconds closing time, 0,6 Amp nominal absorption. Available in the ON/OFF and PROPORTIONAL versions with the opportunity of applying the angular sensor to detect the position of the ball."

Cod. 00200701
"Plastic body, Viton OR and Teflon-PTFE gaskets, plastic ball. Nylon interchangeable flanges with various connections and sizes available. Maximum operating pressure 20bar – 290PSI with flowrate beyond 1000 lt/min on the 2” ½ model. 3 seconds closing time, 0,6 Amp nominal absorption. Available in the ON/OFF and PROPORTIONAL versions with the opportunity of applying the angular sensor to detect the position of the ball."

Cod. RFM78051
REMOVABLE TURBINE FLOWMETER. The Rapid Check flowmeter series is extremely practical when carrying out maintenance operations, and maintains the precision of the standard turbine flowmeters. It is possible to simply unscrew the body to remove, check, and (if necessary) clean the stainless steel axial-flow turbine. A single removable body contains a turbine (with stainless steel, ceramic, ruby or adjustable sapphire bearings) and a sinusoidal-wave or square-wave sensor, 4-20mA.

Cod. 00378051
REMOVABLE TURBINE FLOWMETER. The Rapid Check flowmeter series is extremely practical when carrying out maintenance operations, and maintains the precision of the standard turbine flowmeters. It is possible to simply unscrew the body to remove, check, and (if necessary) clean the stainless steel axial-flow turbine. A single removable body contains a turbine (high or low volume, with stainless steel, ceramic, ruby and adjustable sapphire bearings) and a 4-20 mA sinusoidal-wave or square-wave sensor.

Cod. TXT70395
STAINLESS STEEL (304-316) AXIAL-FLOW TURBINE FLOWMETER. Stainless steel body (304-316) in the versions with antacid plastic ducts (PVDF) or stainless steel ducts. This is the most suitable flowmeter for measuring corrosive and abrasive liquid chemical products at high working pressures. It can be used with a sinusoidal-wave or square-wave sensor, 4-20 mA.

Cod. TXT70196
STAINLESS STEEL (304-316) AXIAL-FLOW TURBINE FLOWMETER. Stainless steel body (304-316) in the versions with antacid plastic ducts (PVDF) or stainless steel ducts. This is the most suitable flowmeter for measuring corrosive and abrasive liquid chemical products at high working pressures. It can be used with a sinusoidal-wave or square-wave sensor, 4-20 mA.

Cod. TX370395
STAINLESS STEEL (304-316) AXIAL-FLOW TURBINE FLOWMETER. Stainless steel body (304-316) in the versions with antacid plastic ducts (PVDF) or stainless steel ducts. This is the most suitable flowmeter for measuring corrosive and abrasive liquid chemical products at high working pressures. It can be used with a sinusoidal-wave or square-wave sensor, 4-20 mA.

Cod. TX370196
STAINLESS STEEL (304-316) AXIAL-FLOW TURBINE FLOWMETER. Stainless steel body (304-316) in the versions with antacid plastic ducts (PVDF) or stainless steel ducts. This is the most suitable flowmeter for measuring corrosive and abrasive liquid chemical products at high working pressures. It can be used with a sinusoidal-wave or square-wave sensor, 4-20 mA.

Cod. TPT70395
STAINLESS STEEL (304-316) AXIAL-FLOW TURBINE FLOWMETER. Stainless steel body (304-316) in the versions with antacid plastic ducts (PVDF) or stainless steel ducts. This is the most suitable flowmeter for measuring corrosive and abrasive liquid chemical products at high working pressures. It can be used with a sinusoidal-wave or square-wave sensor, 4-20 mA.

Cod. TPT70196
STAINLESS STEEL (304-316) AXIAL-FLOW TURBINE FLOWMETER. Stainless steel body (304-316) in the versions with antacid plastic ducts (PVDF) or stainless steel ducts. This is the most suitable flowmeter for measuring corrosive and abrasive liquid chemical products at high working pressures. It can be used with a sinusoidal-wave or square-wave sensor, 4-20 mA.